Search | Statistics | User Listing | Member Roster | Coach DB Forums | Albums
FMC Owner's Forum
Home -> FMC Owner's Forum ->  General Discussion -> Discussion -> View Thread

You are logged in as a guest. ( logon | register )

Throttle pedal bell crank
View previous thread :: View next thread
   General Discussion -> DiscussionMessage format
 
jjveselmj
Posted 2019-11-02 7:26 PM (#7023)
Subject: Throttle pedal bell crank


Location: Nashwauk, MN
(107.77.87.66)
Any body know where I can buy a throttle pedal
bell crank to replace the original zinc bellcrank.
Also what's best way to get it out. I can't see where
Any floor sheet metal can be removed and underneath is next to impossible to get at w/o removing front
Exterior panel. Any ideas appreciated.
Thnx, John Vesel
Top of the page Bottom of the page
B. Sitton
Posted 2019-11-03 8:39 AM (#7024 - in reply to #7023)
Subject: Re: Throttle pedal bell crank


Location: Ignacio Colorado
(71.211.0.173)
I made a few out of steel plate a couple years ago. I’ll check old see it I still have one. I made more of the parts to build more but haven’t assembled those yet. Either way I can come up with one.
Bill
Top of the page Bottom of the page
B. Sitton
Posted 2019-11-03 8:41 AM (#7025 - in reply to #7023)
Subject: Re: Throttle pedal bell crank


Location: Ignacio Colorado
(71.211.0.173)
Oh you remove the box surrounding the steering column base to get to it. Others may have another way, anyone?
Bill
Top of the page Bottom of the page
jjveselmj
Posted 2019-11-03 10:22 AM (#7026 - in reply to #7023)
Subject: Re: Throttle pedal bell crank


Location: Nashwauk, MN
(107.77.87.62)
Thanks for being there for us Bill. I've been communicating with Lou Cruse yesterday and he mentioned you and thought you made the bell cranks. If you have one, let me know at 952/380-7152 and we can make arrangements for shipping. I'll be heading south in a couple weeks (not driving the FMC) so probly ship to Tucson. Not in any hurry as its freezing weather in MN now and I have the FMC covered and put away till spring. But I'd sure like to have one ready. Thanks, Bill talk to you soon. John Vesel J0684
Top of the page Bottom of the page
andy1canada
Posted 2019-11-03 11:16 AM (#7027 - in reply to #7023)
Subject: Re: Throttle pedal bell crank


Location: Victoria, BC. Canada
(108.172.101.233)
"Thanks for being there for us Bill."

Yep, that's our Prez'!

I was sayin' the same thing a few yrs back when #846 decided to suddenly quit on a real bad corner up here on the Sunshine Coast. I managed only to get about half of her width off the one lane hwy as there was hardly any shoulder. I was freaking out as traffic was blazing past at over 50.

After not being able to figure out what was wrong, I managed to get a small tow-truck with a rope (yes, a rope) to pull me around the corner to get me coasting down a long hill to a pull-out. Spent the night there, then with all hope lost, decided to give Billy a call the next morning for some advice. In minutes, he helped me diagnose a simple ignition problem then offered up a jump-wire fix to get me going.

Thanks again - Prez'!

Terry
#846

Top of the page Bottom of the page
LCAC_Man
Posted 2019-11-04 12:14 PM (#7029 - in reply to #7027)
Subject: Re: Throttle pedal bell crank


Location: Oceanside, CA
(70.183.106.155)
I would start with a universal pedal set up like this: https://www.speedwaymotors.com/Speedway-Cast-Aluminum-Accelerator-Th...
and then measure/order a custom cable to fit..
Top of the page Bottom of the page
dkarnath
Posted 2019-11-04 12:29 PM (#7030 - in reply to #7029)
Subject: Re: Throttle pedal bell crank


Location: Medford, OR
(204.10.247.1)
Wrong thread Len...But that is a good priced pedal assembly.
Top of the page Bottom of the page
Jump to forum :
Search this forum
Printer friendly version
E-mail a link to this thread

Go to FMCowners.com HomeRunning MegaBBS ASP Forum Software
© 2002-2024 PD9 Software
(Delete all cookies set by this site)